Upskilly & Stuff – Page 2 – Deborah Makarios

March 31, 2018

Upskilly & Stuff 3: The Petticoat, Skirt or Slip

One pattern, three garments: a skirt, an underskirt – which is to say, a petticoat – or an underskirt which has the added benefit of being slippery and thus keeps layers of clothing from sticking to each other – or the wearer. (Slips, I feel, are massively underappreciated in this day and age. I have five.)

However, I would not recommend making the third of those three options unless you have the patience of Job (with less tendency to complain), as slippery fabrics are definitely advanced work.

On the other hand, if you still believe that everything in this world is subject to the laws of physics, do try making something with slippery fabric. You will find it very educational.

I decided to stick to the simple petticoat: a basic skirt designed to be worn under another skirt. It doesn’t have to look good; all it has to do is keep the sunlight from advertizing your legs to the world at large. A low-pressure project, in fact.

For this project I did my first bit of pattern-making. Imagine, if you will – no, never mind imagining, it’ll take too long to describe. Here’s a picture.

This represents a quarter of the whole skirt. The straight line down the left goes on the fold (fabric folded in half lengthwise), so after cutting around the other three sides you end up with a half-skirt piece. Cut two for a front and a back. The note on the right is to remind myself to add seam allowance there. The straight bit at the top of the right edge is to make the waistband-making easier.

The most important thing to remember when drafting a skirt pattern is that unless you are putting in some kind of fastening like a zip or buttons, the waist will need to go over your hips, so the waist measurement should actually be your hip measurement plus a little bit for leeway.

Straight down 3cm for the waistband (or more if you’re using wide elastic or the like) and then draw a straight line from there out to the desired length and width. I originally drew the pattern out to 40cm wide at 75cm length, but then realized it wouldn’t work with the fabric I chose (a nice worn-smooth piece of old sheet) unless I put in another seam.

Shorter slip, or three seams to sew? I decided simplicity was the way to go. Incidentally, one of the useful things about a skirt pattern that extends a line is that if you need it shorter, you can just measure the desired length down the straight side, mark a line across, and whack off the extra with a pair of scissors. (Want a longer skirt later? Get out the ruler and extend the line on another piece of paper.)

So, having sorted out the pattern, I cut two as instructed (not forgetting the seam allowance on what I might go so far as to call the hypotenuse) and pinned them together – wrong sides together.

A dreadful mistake? No, the first step of a French seam, a very useful seam which leaves you with no distressed edges hanging about on the inside of your garment (so it lasts longer) and only two rows of stitching to sew (unlike, say, a Hong Kong finish).

Press at every opportunity, is my advice. I pressed in between each stage of the seams, pressed the first fold down for the waistband, pinned, pressed… It was going to be an elasticated-waist petticoat, but the elastic was too blasé for my liking, and so I ended up sewing a strip of bias binding closed (hip measurement + plenty extra for ties) and making it a drawstring petticoat instead.

Slightly less convenient, perhaps (the way you need to arrange the gathers each time is a little irritating, I confess), but superior in two ways: I won’t need to worry about replacing elastic when it dies, and the waistband is now fully adjustable.

I could have continued on and finished it off with the hem, but as some of the fabric is, in the nature of things, not cut along the grain, I decided it would be best to let it hang overnight to avoid subsequent wonkiness. Here it sits on the exoskeleton, then, waiting for me to mark a straight hem, pin, press and sew it.

Not, perhaps, the most beauteous of garments, but that’s the good thing about petticoats: no one sees them but yourself. (So if you have a secret passion for scarlet hues or lavish lace, knock yourself out. No one will ever know…)

It’s a very empowering sort of garment to make: it’s simple, it’s undemanding, and it’s a “real thing” – a proper garment, unlike, say, an apron which you just tie on over your real clothes. You can make one in an afternoon, and making your own pattern is pretty simple too (a very long ruler helps, as does thinking it out on paper first). A garment made to measure from your own personal pattern – what could be better?

For this project, I practiced pattern-making, laying out a pattern on fabric, measuring & cutting, French seams, making a casing (I’ve only just realized it’s basically the same as a hem, but upside down) and threading a casing. (And hemming again, once I’ve done that bit.)

The next Upskilly step takes us on to the nightgown – here come sleeves!

February 23, 2018

Upskilly & Stuff 2: The Apron

Rectangle, rectangle, string, string, string.

One big rectangle for the bottom part; one smaller rectangle (optional) for the upper part; and three ties: one to go round your neck (unless you opted out of the upper part or wish to pin the bib on in the old-school manner) and two to fasten the whole shebang around your waist. 1-2 rectangles + 2-3 strings = apron.

I actually cheated a bit: I cut the top part and the bottom part (bib and, er, skirt?) in one – a bit wasteful of fabric, but it worked for the piece I had. Piece of fabric, bias binding for ties, and I was good to go – or was I?

The bias binding was, frankly, the colour of empty sausage casings; the fabric was bright white. Two problems there: one, they don’t go; and two, white is not a good colour for an apron unless you like to spend a lot of time soaking things in stain remover.

Solution: the left-over packet of dye from the triangle dress. Since the uncut fabric was too heavy (i.e. would have resulted in a lighter colour) I cut out the apron shape first, and then stay-stitched the raw edges (a line of stitches close to the edge, to control fraying & distortion), before flinging it, along with the bias binding, into the dye bath.

Observe the line of white stay-stitching.

Learning moment: bias binding, be it never so starchy, will lose its shape the minute you get it wet, and become little more than a tragic draggle. Incidentally, I was unsure to begin with whether the bias binding was natural fibre or something which wouldn’t take the dye. So I snipped a little bit off and set it on fire. General rule of thumb: if it burns, it’s dyeable. If it melts, you’re wasting your time, because a) it won’t dye and b) it’ll make a rotten apron. (Please observe due caution and common sense when setting things on fire.)

Once the dyeing was completed and the materials had dried (hanging on the line for a night, which tells you how hot it’s been here lately) I ironed them. Then I pinned one end of the bias binding (folded double) to one end of the top, and figured out how much I’d need for the neck band. (Never forget to add seam allowances.)

I cut the remaining piece in half for the ties, pinned the right sides of each piece together, sewed them into tubes and turned them right side out again. (I could have whipped the two edges together if it had stayed in the classic bias binding shape, but alas, it was not to be. Perhaps I should have staystitched that as well.) A bodkin can be useful for turning the tube (I used the safety-pin approach) but make sure that this is a sewing bodkin, and not a dagger, please!

Then – you guessed it! – press ’em flat. Then back to the pinning: pinning a ‘hem’ like the one I used on the kerchief around the raw edges of the apron piece (thus concealing the stay-stitching, which failed to dye), and attaching the tapes in the right places. My piece of fabric was already hemmed top and bottom, so I had to figure out a way to attach the neck tape which wasn’t built into the hem. (I basically just gave the hem another fold with the neck tape tucked into it.)

Then the sewing! This went pretty well until I got to a corner where two sets of double-fold hem and a tape met. The fabric I’m using is something like a heavy canvas or denim, and it makes for some chunky folds. Had I thought of this earlier, I could have taken the sewing advice I saw once: put it on a piece of wood and flatten it with a hammer. But I managed to pass through the edge, and went back to sew the rest firmly in place afterward by hand. Also by hand (because I forgot at the make-a-tube stage): sewing the free ends of the waist tapes closed.

The exoskeleton models the apron, having just enough neck for it to work.

Ta da! It is done, finished, complete. As far as I can see, it has only two issues: the front gapes a bit (still, it’s an apron, not a bib) and it’s kind of… pink. It remains to be seen whether I find it too pink to wear or not.

But, whether I keep it or not, I’ve practiced measuring, cutting, hemming, messing about with bias binding and attaching tapes.

Next month: a simple skirt or slip!

January 26, 2018

Upskilly & Stuff 1: The Kerchief

What could be a simpler beginning than a kerchief? Cut a square, hem the edges. Job done.

I’ve been meaning to make a brown kerchief for some time, all the more since I bought a dress in brown & cream and had nothing to wear with it that really went. In considering the brown fabrics in my stash, I discovered these:

Would you believe these are all from the same bolt of fabric, and purchased at the same time? At the top is the fabric as it came from the bolt; in the middle is the same fabric made up and lightly worn, and at the bottom is the same fabric made up and heavily worn. What can I say? It was only three dollars (NZ) per metre and I was a poor student.

So I’m not expecting this to hold its colour – but while it does, the middle fabric is a near perfect match for the brown of my dress. For some reason it (the fabric, not my dress) was in the form of a partially cannibalized medieval tunic. Why I made (or indeed wore) a medieval tunic I could not tell you, but there it is, and eminently fit for purpose.

The next consideration is size. My head is unusually small, and my smallest kerchief (which I only use for a splash of colour on top of a larger plain one) is 45 x 50cm. So that’s the minimum for me, plus a couple of centimetres each way for the hem.

Suggestion: measure around your head, add maybe 20cm allowance for tying (or more if your fabric is thick) and make that the hypotenuse of your kerchief. Remember: the square of the hypotenuse is equal to the square of the other two sides.

My ex-tunic is about 57cm wide, so I’m going to use that as my base: trim off the old raggedy hem and start afresh, beginning by drawing a thread and cutting it square. (Information on why and how can be found here.)

Full disclosure: I also got out the iron and pressed the rumpled edges down – despite it being 27*C – because I have reached the age where I like to take my time and do the job properly in all its details. If you’re not fussy about things coming out just so, then feel free to skip that step – just don’t blame me if the results are a little more slapdash than you were anticipating.

So, I’ve squared my edge, I’ve pressed it, and I’ve cut out my square. Now, technically, I already have a kerchief here, but it isn’t finished. There may be some who like the frayed look of an unfinished edge – yes? Raise your hand… and smack yourself firmly round the head with it and promise to reform hereafter. An unfinished edge is not only a fraying and falling apart edge with a short life span ahead of it, it is distressed. What kind of monster wishes to distress the poor fabric? Be kind; finish it properly.Now for the hem. My fabric’s middling thickness, so I’m going to do a simple double-fold hem. If it were thinner, I’d do a rolled/handkerchief hem by hand, but it would be too bulky with this fabric – it’s bulky enough as is, since I’m doing a narrowish hem to keep as much width in the kerchief as possible. Pressing with an iron is an option here, too, but I just use a firm finger-press unless the fabric’s being obstinate, followed by a series of pins.

I was originally planning to sew this by machine (I even oiled the machine specially) but then I discovered I didn’t have any thread which matched closely enough. So I’m doing a blind stitch hem, which comes out almost invisible on both sides – although how invisible remains to be seen when the fabric fades.

Here’s what it looks like on the wrong side:

The background (at top) is the dress – good match, isn’t it? My apologies for the blurriness – the camera phone doesn’t seem keen on close-ups. Here’s what the right side looks like (and this time, please note, the kerchief is at the top and the dress at the bottom):

The finished kerchief measures 57 x 56cm. Quite how this happened, considering the beginning measurements, I do not know. I assume it has something to do with flattening out the edges (formerly wedged against seams) with the iron.

But finished it is! The first step on the Upskilly & Stuff ladder has been taken; measuring, cutting, pressing, pinning and hemming have all happened, and a wearable garment is complete.

Next month: the apron!
In the meantime, I’d love to hear what you’ve been making – feel free to leave a comment below.

Please note: if you are unable to find the comment section, click on the post title. You’ll be taken to the full-width post page with comment section at end.